PowMr 60A MPPT Solar Charge Controller 12V/24V/36V/48V DC 0 Layer LCD Display US. PowMr Solar Charger Controller MPPT 60A 12V 24V 36V 48V Blacklight LCD Regulator Max PV Input 150VDC Support Lithium batteries. POWMR 60Amps MPPT solar charge controller is based on an advanced maximum power point tracking(MPPT) technology developed, dedicated to the solar system, the charge controller conversion efficiency up to 97%. M6-PRO Support one-key restore function.
MPPT 30A/40A/50A/60A solar charge controller 100% MPPT technology 0 Layer, easy installation, easy setup Built-in DSP controller with high performance Automatic switch for 12V/24V/36V/48V battery bank 3-stage charging optimizes battery performance Overcharge protection, Input PV polarity reverse protection, Output limited current protection, Over-temperature protection Troubleshooting promotion function. Suitable for battery types such as sealed lead acid, vented gel, and lithium battery, etc Easy to be mounted. Technical Specification for Selection Guide.MPPT Maximum power point tracking automatically. 3-stage:constant current(MPPT), constant voltage(Absorption Voltage), floating charge. Dynamic response and recovery time. >98.1 % (Voc is 1.5 or 2 times than battery, then it's the best efficiency). VOC from PV Make sure the Voc of PV meeting the requirement as right.
Voc is 1.5 or 2 times than battery, then it's the best efficiency. The maximum PV input voltage (Voc). DC190VThe controller can't work at this voltage of long duration that will break controller. Please refer to the Input voltage from PV.
The maximum PV input power The total power rated of PV can't be over this watt that will break the controller. Selectable battery type(default is Sealed). Vented/ Sealed / Gel / NiCd / Lithium battery(defined voltage for other battery by user). Refer to Batteries charging reference.
14.2V-(Max temperature-25 °C)0.3. Output power will reduce when it's more than 70 °C. Output power will be normal when it's less than 55 °C. Imported materials, Accord to EU standards, Industrial grade range. Meet 2002/95/EC; No cadmium, hydrides, and fluorides.
Accord to CE, PSE, FCC, EMC, EN60950. Accord to EN6W00, EN55022, EN55024. 1 x 60A MPPT Solar Charge Controller. 1 x English User Manual. Battery must be connected first.
NEVER connect the solar panel array to the controller without a battery. Ensure input voltage does not exceed 190 VDC to prevent permanent damage. Do NOT let the positive (+) and negative (-) terminals of the battery touch each other. Do NOT connect any inverters or battery charger into the load terminal of the charge controller. Place the controller on a vertical surface protected from direct sunlight, high temperatures, and water.Make sure there is good ventilation. Please check for Clearance, verify that there is sufficient room to run wires, as well as clearance above and below the controller for ventilation. The clearance should be at least 3 inches (75mm).
Please pay for your order within 48 hours before order close. Please check your address information before place the order. We are not responsible for wrong or undeliverable address. Response time 1 Hrs(WorkingDay).
"Highly Quality first, customer orientation"is our purpose. PowMr will be committed to provide the best service to you!
We will reply you within 24 hours. Feedback is important to us, we will leave positive to our customers. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Alternative Energy Chargers & Inverters".
The seller is "yoosmart-com" and is located in this country: US. This item can be shipped to United States.